Liebherr NoFrost Freezer With Wlectronic Controls 7082 308-00 User Manual download pdf (Page 10)

GN..3

Dimensions

The external dimensions of the appliance can be seen on

ﬁg. S and in the table below.

Gross capacity External dimensions [mm]

of appliance [l] A B C D E F

(see type plate)

162 (18..) 1250 600 631 614 644 1179

200 (21..) 1447 600 631 614 644 1179

238 (25..) 1644 600 631 614 644 1179

276 (28..) 1841 600 631 614 644 1179

188 (20..) 1250 660 683 662 704 1287

233 (24..) 1447 660 683 662 704 1287

279 (29..) 1644 660 683 662 704 1287

324 (33..) 1841 660 683 662 704 1287

Installation instructions

- Do not install models without side-wall heating side-by-

side with another refrigerator or freezer. This is important

to prevent condensation and consequential damage from

it.

- Models with side-wall heating are designed for side-by-

side installation; they are designed for combination with a

refrigerator.

Contact your dealer for more information.

- Attachment instructions are supplied in the accessories

bag of the appliance with side-wall heating.

Changing over door hinges

The door hinges can be changed from one side to the other

if required.

W With the door open, lever out plinth panel 1 on the hinge

side with a screwdriver and remove from front.

- Lever out cover 2 with a screwdriver.

Close door.

- Unscrew screw M5 3.

W Pull hinge component 4 with hinge pin 5 out from un-

derneath and remove.

W Open door, lift out at bottom and remove; do not lose the

spacer 6.

W Transfer all hinge components onto the other side:

- Lever out covers 8 with a screwdriver at the front and

remove at an angle from below. Remove hinge pin 7

and insert on the opposite side. Use the hexagon

socket on the open-ended spanner provided (spanner

width 5). Fit covers 8 again: insert at rear and click into

place at front.

- Bottom: Using a screwdriver, remove the spacer 9 and

replace on the other side.

W Re-attach the door:

- Remove plugs bo from the door mounting points and

replace on the other side.

- Suspend door with spacer 6 in hinge pin 7, close door.

- Rotate hinge component 4 by 180°, remove hinge pin 5,

turn by 180° and replace. Mount both parts in the hinge

bp: slide the pin into the door mounting through the

hinge, tilt in the hinge component, slide up and attach

with screw 3.

W Align the door ﬂush with the body of the appliance using

the slot on the hinge bp, then tighten screw 3.

W Attach the plinth panel 1 and click into place by press-

ing.

Instructions for installation and modiﬁcation

W With the door open, insert the cover 2 in the plinth panel

at the front and click into place at the back.

W Transfer* door handle bl and plugs bm: With the door

open, carefully lift out the pressure plates* bn at the front

and slide away; unscrew handle.

Re-assemble in reverse order: replace the pressure plates

and click into position.

Insertion into row of kitchen units

Fig. U. 600 mm appliances can be installed in a row of

kitchen units. To adapt the height of the appliance to the

surrounding furniture a top unit 1 can be added.

A gap of at least 50 mm depth must be provided behind and

along the entire width of this unit so as to ensure sufﬁcient

ventilation. The area of ventilation underneath the ceiling

should be at least 300 cm

. The greater the area the more

economically the appliance will run.

W When installing with standard kitchen units (max. depth

580 mm) and decor panels of max. 2 mm thickness, the

appliance can be set up right next to the kitchen unit.

The door protrudes 34 mm from the side of the kitchen

unit and 51 mm at the front. This enables it to be opened

and closed without difﬁculty.

W When setting up the appliance next to a wall 4, a mini-

mum distance of 36 mm must be provided on the hinge

side between the appliance and the wall (for the handle

when the door is open).

1 top unit 3 kitchen unit side panel

2 refrigerator/freezer 4 wall

Notes on assembling decor panels

with white appliances of width B = 600 mm and height

A = 1841 mm:

Decor panel and frames can be attached to the door of your

appliance to match or contrast it to the existing kitchen

colour scheme.

The panels are available from your kitchen furniture supplier.

The frames can be ﬁtted later and are available from your

dealer.

If you wish to ﬁt the decor panels yourself, you will need

a drill or a rechargeable screwdriver to pre-drill the retain-

ing holes. The door handles are to be replaced by the rigid

handles included in the decor frame retroﬁt kit.

For further instructions and dimensions see the installation

instructions included in the retroﬁt kit.

1 2 ... 5 6 7 8 9 10 11

Comments to this Manuals

No comments

Liebherr NoFrost Freezer With Wlectronic Controls 7082 308-00 User Manual Page 10

Comments to this Manuals

Related products and manuals for Fridge-freezers Liebherr NoFrost Freezer With Wlectronic Controls 7082 308-00