Liebherr FT 2900 User Manual download pdf (Page 3)

Switching the appliance on and off

To switch the appliance on: Connect the appliance to the mains

- the appliance is switched on.

To switch the appliance off: Pull out the mains plug or remove/

unscrew the fuse.

Setting the temperature

Turn the arrow on the temperature control to a

setting between 1 und 7.

Setting 1 = lowest cooling setting

Setting 7 = highest cooling setting

The temperature control is in the cover grille for

the compressor department on the right-hand

side wall of the appliance.

Cooling

This appliance can be used for chilling all types of drinks and food.

It must not be filled higher than the stacking mark

on the inside.

Cleaning

Before cleaning always switch off the appliance.Pull out the

mains plug or remove/unscrew the fuse.

• Remove the plug from the drain

opening.

• To collect the thawed water, place a

flat container below the refrigerator.

• Clean the inside, equipment parts

and outer walls with lukewarm water

and a little detergent. Do not use

abrasive or acid cleaners or chemical

solvents.

• Ensure that no cleaning water pene-

trates into the electrical components

or ventilation grille.

• Dry all parts well with a cloth.

• The ventilation grilles should be cleaned regularly. Dust deposits

increase energy consumption.

Do not use steam cleaners because of the risk of injury and

damage.

Shutting your appliance down

If your appliance is to be shut down for any length of time, switch

it off and disconnect the plug or remove the fuse. Clean the appli-

ance and leave the lid open in order to prevent unpleasant smells.

Special features

• barrel lock

• clip-in baskets

Barrel lock: Place the barrel lock in

the opening provided in the lid, turn

the key and remove.

The appliance complies with the relevant safety regulations and

EC directives 2004/108/EC and 2006/95/EC.

Setting up

• Avoid positioning the appliance in direct sunlight or near cookers,

radiators and similar sources of heat.

• The floor on which the appliance stands must be horizontal and

level.

• Do not cover the gap

between the lower edge

of the appliance and the

floor, as the refrigeration

unit has to be supplied

with air for cooling.

• There must be a gap of at

least 20 cm between the

ventilation grille and the

wall. This gap must be

kept clear and the ventila-

tion openings uncovered.

• Do not place any objects

immediately next to the outer housing of the appliance. There

must be a gap of at least 20 mm all round in order to ensure

adequate heat discharge.

• Standard EN 378 specifies that the room in which you install

your appliance must have a volume of 1 m

per 8 g of R 600a

refrigerant used in the appliance, so as to avoid the formation of

inflammable gas/air mixtures in the room

where the appliance is located in the

event of a leak in the refrigerant circuit.

The quantity of refrigerant used in your

appliance is indicated on the type plate.

• Do not connect the appliance to the supply

with other equipment using an extension

cable - risk of overheating.

• Attach the bottle opener ➊ (if provided) to

the appliance and suspend the crown cork

bin ➋ on the screws attached beneath it.

Connecting to the mains

Power supply (a.c.) and voltage at the operating point must comply

with the details on the type plate. The type plate is located on the

rear of the appliance. The socket must be fused with a 10 A fuse

or higher, it must be away from the rear of the appliance and must

be easily accessible.

Connect the appliance with a properly earthed fused plug

and socket only.

Malfunctions

You may be able to rectify the following faults by checking

the possible causes yourself:

• Appliance does not function:

- Is the plug correctly fitted in the mains socket?

- Is the socket fuse intact?

• The temperature is not low enough:

- Is the temperature setting correct (see "Setting the temperature")?

- Does the separately installed thermometer show the correct

reading?

- Is the ventilation system working properly?

- Is the appliance set up too close to a heat source?

If none of the above causes apply

and you cannot rectify the fault

yourself, contact the nearest cus-

tomer service department stating

the type of appliance ➊, service

number ➋ and appliance number ➌

as indicated on the type plate. The

type plate is located on the rear of

the appliance.

1 2 3

Comments to this Manuals

No comments

Liebherr FT 2900 User Manual Page 3

Comments to this Manuals

Related products and manuals for Refrigerators Liebherr FT 2900