Fig. 6
(1) Ice cubes
The numbers indicate the storage time in months for
different types of frozen foods. The storage times given
are guidelines.
5.15 Refrigerant accumulators
These refrigerant accumulators prevent the temperature
from rising too fast when power failures occur.
5.15.1 Using refrigerant accumulators
u
Place the frozen refrigerant
accumulators in the top
front area of the freezer
compartment on top of the
freezer goods.
5.16 IceMaker
The IceMaker is located in the fifth drawer compartment
from the top. The drawer is labeled “IceMaker”.
Make sure that the following conditions are fulfilled:
-
The appliance is level.
-
The appliance is connected to the electricity supply.
-
The minimum freezer temperature is 14 °F (-10 °C).
-
The IceMaker is connected to the water supply.
-
All air was bled from the waterline before starting the
icemaker. The icemaker will only work if there is no air
in the waterline.
5.16.1 Switching on the IceMaker
Fig. 7
u
Pull out the drawer.
u
Press On/Off button
Fig. 7 (1)
so that the LED
Fig. 7 (2)
lights up.
u
Push in the drawer.
w
The IceMaker symbol
Fig. 2 (12)
shines.
Note
u
The IceMaker only produces ice cubes when the
drawer is completely closed.
5.16.2 Producing ice cubes
The production capacity depends on the freezer tempera-
ture. The lower the temperature, the more ice cubes can
be produced in a certain period.
The production capacity is 90- 100 ice cubes in 24 hours
at a freezing temperature of 0 °F (-18 °C).
To have the maximum capacity of approx. 130 ice cubes
in 24 hours, activate the SuperFrost Function. Be aware
that this increases the energy consumption because the
compressor will run constantly.
The ice cubes fall out of the IceMaker into the drawer.
When the ice cubes reach a certain height in the drawer,
no more ice cubes can be produced. The IceMaker will
not fill the drawer to the top.
If large quantities of ice cubes are required, the complete
IceMaker drawer can be swapped with the neighboring
drawer. When you close the drawer, the IceMaker auto-
matically restarts production.
When the IceMaker is switched on for the first time, it may
take up to 24 hours for the first ice cubes to be produced.
Note
Particles may accumulate in the IceMaker or water line the
first time the appliance is used or after an extended period
out of service.
u
To achieve this, do not consume or use the ice cubes
that are produced within 24 hours.
5.16.3 Setting the water supply time
The opening time of the valve on the IceMaker can be
adjusted if, for example, the water pressure in the pipe is
too low or too high.
The water supply time can be set in stages from E1 (short
supply time) to E8 (long supply time). The default setting
is E3.
u
Activate setting mode: press and hold the SuperFrost
button
Fig. 2 (5)
for approximately 5 s.
w
S is shown on the display.
w
The Menu symbol
Fig. 2 (9)
lights up.
u
Using the Up button
Fig. 2 (3)
or Down button
Fig. 2 (4)
,
select E.
u
To confirm: briefly press the SuperFrost button
Fig. 2 (5)
.
u
To increase the water supply time: press the
Up button
Fig. 2 (3)
.
u
To decrease the water supply time: press the
Down button
Fig. 2 (4)
.
u
To confirm: press the SuperFrost button
Fig. 2 (5)
.
u
Deactivate setting mode: press the On/Off button
Fig. 2 (1)
.
-or-
u
Wait 5 mins.
w
The temperature is again displayed on the temperature
display.
Operation
* Depending on model and options 9
(32 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals